Process Calibration Tools

• Best in class 0.2 % accuracy
• 0.01 mA resolution and sensitivity
• Measure 4 to 20 mA signals without ”breaking the loop”
• Dual backlit display with both mA measurement and percent of 4 to 20 mA span
• Measure 10 to 50 mA signals in older control systems using the 99.9 mA range
• Automatically change the 4 to 20 mA output for remote testing
• Measure 4 to 20 mA signals with in-circuit measurement
• DC voltage measurement to verify 24V power supplies or voltage I/O signals
• Source DC voltage to test input devices that accept a 1-5V or 0 to 10V signals
• Simultaneous mA in-circuit measurement with 24V loop power for powering and testing transmitters
• Source 4 to 20 mA signals for testing control system I/O or I/Ps
• mA output linear ramp or 25% step output
• Automatically change the 4 to 20 mA output for remote testing

• Measure volts, mA, RTDs, thermocouples, frequency, and ohms to test sensors, transmitters and other instruments
• Source/simulate volts, mA, thermocouples, RTDs, frequency, ohms, and pressure to calibrate transmitters
• Power transmitters during test using loop supply with simultaneous mA measurement
• Measure/source pressure using any of 29 Fluke 700Pxx Pressure Modules
• Create and run automated as-found/as-left procedures to satisfy quality programs or regulations. Record and document results
• Holds up to a full week of downloaded procedures and calibration results.
• Use many features like auto step, custom units, the user entered values during the test, one-point and two-point switch testing, square root DP flow testing, programmable measurement delay etc.
• Easy to use
• Three-year warranty
• Bright white dual display. Read both sourced and measured parameters simultaneously.
• Multilingual interface
• Rechargeable Li-Ion battery for 10-hour uninterrupted use. Includes gas gauge.
• Handling of fast pulsed RTD transmitters and PLCs, with pulses as short as 1 ms.
• Delivered with DPC/Track Sample software.
• Compatible with many Asset Management software packages

• Works with multiple masters, burst mode, and multi-drop configurations.
• Is easy to update as additional instruments are added and new HART versions are released.
• Interrogate to determine device type, manufacturer, model, tag.
• Reconfigure the sensor mapping of dual sensor temperature transmitters.
• Read HART PV function and smart transmitter digital output while measuring analog mA output.
• Read and write HART configuration functions to make field adjustments to PV range points, damping, and other top-level configuration settings.
• Re-label smart transmitters by reading and writing to the HART tag field.
• Three-year warranty
• Bright white dual display. Read both sourced and measured parameters simultaneously.
• Multilingual interface
• Rechargeable Li-Ion battery for 10-hour uninterrupted use. Includes gas gauge.
• Handling of fast pulsed RTD transmitters and PLCs, with pulses as short as 1 ms.
• Delivered with DPC/Track Sample software.
• Compatible with many Asset Management software packages.
• HART Capabilities

• Measure volts, mA, RTDs, thermocouples, frequency, and ohms to test sensors, transmitters and other instruments
• Source/simulate volts, mA, thermocouples, RTDs, frequency, ohms, and pressure to calibrate transmitters
• Power transmitters during test using loop supply with simultaneous mA measurement
• Measure/source pressure using any of 29 Fluke 700Pxx Pressure Modules
• Create and run automated as-found/as-left procedures to satisfy quality programs or regulations. Record and document results
• Holds up to a full week of downloaded procedures and calibration results.
• Use many features like auto step, custom units, user-entered values during the test, one-point and two-point switch testing, square root DP flow testing, programmable measurement delay etc.

• More precise measurement and calibration source performance, accuracies of 0.01%.
• Two separate channels; measure, source and view process signals simultaneously
• Measure volts, mA, RTDs, thermocouples, frequency, and resistance to test sensors and transmitters
• Source/simulate volts, mA, thermocouples, RTDs, frequency, and pressure to calibrate transmitters
• Measure or source pressure* using any of 29 Fluke 700Pxx Pressure Modules
• Source mA with simultaneous pressure measurement to conduct valve and I/P tests
• Integrated pressure switch test allows you to capture the set, reset and deadband of a switch
• Memory storage for up to 8 calibration results, return stored calibration data from the field for later analysis
• Transmitter error% calculation, interpret calibration results without a calculator
• Perform fast linearity tests with auto step and auto ramp features
• Power transmitters during test using 24 V loop supply and simultaneous mA measurement
• Store frequently-used test setups for later use
• Frequency totalizer and frequency pulse train source mode for enhanced flowmeter testing
• HART mode inserts 250-ohm resistor in mA measure and source for compatibility with HART instrumentation
• Custom RTD curves, add calibration constants for certified RTD probes for enhanced temperature measurement.
• New voltage input protection design for improved reliability
• Three-year warranty

We are one of the leading wholesale traders of Fluke 725Ex Intrinsically Safe Multifunction Process Calibrator.

Features:-

• ATEX II 1 G Ex ia IIB 171°C KEMA 04ATEX 1303X
• I.S. Class I, Division 1 Groups B-D, 171°C compliance
• Measure Volts dc, mA, RTDs, thermocouples, frequency and ohms
• Source or simulate Volts dc, mA, RTDs, thermocouples, frequency and ohms
• Two channel simultaneous source and measure capability for calibration of transmitters
• Power transmitters with internal loop supply
• Store frequently-used test setups for later use
• Pressure measurement to 3,000 psi/200 bar using any of the 8 intrinsically safe Fluke 700PEx Pressure Modules calibrate pressure transmitters and me/P devices
• Pressure switch test function to capture set, reset and deadband values
• Compact size and weight
• Simple, push-button user interface
• Rugged and reliable, for field use

The Fluke 729 Automatic Pressure Calibrator has been designed specifically with process technicians in mind to simplify the pres­sure calibration process and provide faster, more accurate test results. Technicians know that calibrating pressure can be a time-consuming task, but the 729 makes it easier than ever with an internal electric pump that provides automatic pressure generation and regulation in an in an easy-to-use, rugged, portable package.

The ideal portable pressure calibrator, the 729 allows you to simply type in a target pressure, and the calibrator will automatically pump to the desired set-point. Then, internal fine adjustment con­trol automatically stabilizes the pressure at the requested value.

The Fluke 729 can also automatically test multiple pressure test points and automatically document the results. Calibration is as easy as typing in the starting and ending pressure and the number of test points and tolerance level. The 729 does the rest.

Built-in HART communication capabilities enable HART transmitter mA adjustments, light HART configuration and the ability to adjust to applied 0% and 100% values.

Upload and manage documented calibration results with DPCTrack2™ Calibration Management Software, making it easy to manage your instrumentation, create scheduled tests and reports, and manage calibration data.

With three ranges to choose from, 30 psi (2 bar, 200 kPa), 150 psi (10 bar, 1 MPa) and 300 psi (20 bar, 2 MPa), Fluke 729 Automatic Pressure Calibrators are designed to perform when and where you need them

Features:-

• Automatic pressure generation and regulation to 300 psi
• Easily document the process using onboard test templates
• Automatic internal fine-pressure adjustment
• Measure, source and simulate 4 to 20 mA signals
• 24V loop power for powering transmitters for tests
• Bright dual/triple-channel color graphical display
• HART communication for testing HART smart transmitters
• Built-in leak testing for verifying test setups for leakage
• Rugged portable design with a standard 3-year warranty
• Fluke Connect® App compatibility
• Measure temperature with the optional 720RTD probe
• Measure Vdc for testing 1 V dc to 5 V dc output transmitters
• Compatible with 700 Series and 750 Series pressure modules
• Upload documented test results to DPCTrack2™ Calibration Management Software
• Innovative semi-rigid carrying case designed for field work